保溫卷簾門是一種帶有特殊功能的卷簾門，其主要特點是保溫性能尤其出色。保溫卷簾門采用鋁合金或鍍鋅鋼板雙層一次輥軋成型，型材中間填充綠色發泡材料，能夠有效噪音，提高型材的抗彎性，具有良好的保溫效果。

Thermal insulation roller shutter door is a type of roller shutter door with special functions, which is characterized by particularly excellent thermal insulation performance. The insulation roller shutter door is formed by double layer rolling of aluminum alloy or galvanized steel plate, and the middle of the profile is filled with green and environmentally friendly foam material, which can effectively eliminate noise, improve the bending resistance of the profile, and have a good insulation effect.

保溫卷簾門型材表面為多層烤漆或薄膜層，抗陽光照射、抗雨水、抗腐蝕、抗劃傷。可采用外裝、內裝、中裝多種安裝方式，遇微碰撞后可反彈恢復，如劃傷可做到單片更換。采用管狀式電機配套安裝，體積小、造型美觀。

The surface of the insulated roller shutter door profile is made of multiple layers of baking paint or film, which is resistant to sunlight, rain, corrosion, and scratches. Multiple installation methods can be used, including exterior, interior, and interior. In the event of minor collisions, it can rebound and recover. If there are scratches, it can be replaced as a single piece. Equipped with a tubular motor for installation, it has a small volume and beautiful appearance.

保溫卷簾門安裝方法：

Installation method for insulation roller shutter door:

1、在安裝的門框框口畫線標出相應的位置，同時注明尺寸大小，需要注意的是框內高度要比門扇的高度高一些。安裝在門外側的保溫卷簾門通常能使該門的K值少提高45%，在安裝時保證卷簾面板與門框的間距≥40mm。

1. Draw lines and mark the corresponding positions at the mouth of the installed door frame, while indicating the size. It should be noted that the height inside the frame should be higher than the height of the door leaf. The insulation roller shutter door installed on the outside of the door can usually increase the K value of the door by at least 45%, and ensure that the distance between the roller shutter panel and the door frame is ≥ 40mm during installation.

2、為了將保溫卷簾門的門框固定，要先拆掉門框下部的固定板，在洞口兩側的地面要事先預留凹槽，然后進行校正，待合格后固定木楔，將門框鐵腳與預埋鐵板件焊牢。

2. In order to fix the door frame of the insulated rolling shutter door, the fixing plate at the bottom of the door frame should be removed first. Grooves should be reserved on the ground on both sides of the opening in advance, and then corrected. After passing the inspection, wooden wedges should be fixed, and the iron feet of the door frame should be welded firmly with the embedded iron plate.

3、安裝門扇主體，注意一定要保證保溫卷簾門與墻體結成整體，封閉性要做好，然后粉刷洞口及墻體。粉刷完畢后，門縫應均勻平整，開啟保溫卷簾門應該自由輕便，不得有過緊、過松和反彈現象。

3. When installing the main body of the door leaf, be sure to ensure that the insulation roller shutter door is integrated with the wall, and the sealing should be done well. Then, paint the openings and walls. After the painting is completed, the door seam should be even and flat, and the insulation roller shutter door should be opened freely and lightly without any tightness, looseness, or rebound.

保溫卷簾門安裝要點：

Key points for installing insulation roller shutter doors:

(1)保證保溫卷簾門在關閉時的密封性，座條必須與接觸面密閉，通常可以在其下端設置一條彈性密封型材。

(1) To ensure the sealing of the insulation roller shutter door when closed, the seat strip must be sealed with the contact surface, and an elastic sealing profile can usually be set at its lower end.

(2)導軌上必須有密封裝置，有彈性的橡膠條或者硅化毛條，加有密封裝置的導軌的寬度須與葉片的厚度相適應。

(2) There must be a sealing device on the guide rail, with elastic rubber strips or silicified wool strips. The width of the guide rail with a sealing device must match the thickness of the blades.

(3)為了減少從卷簾門包箱口生產的熱量損失，必須使處于關閉狀態的卷簾板壓住卷簾包箱的外側面，必要時在相應縫隙處加裝密封條。

(3) In order to reduce the heat loss produced from the opening of the rolling shutter door packaging box, it is necessary to press the closed rolling shutter board against the outer side of the rolling shutter packaging box, and if necessary, install sealing strips at the corresponding gaps.

(4)為了符合減少構件熱損失的要求，需要在暗裝卷簾包箱朝寅一面加上厚度在20mm以上的保溫材料，縫隙處可用如密封條等密封。

(4) In order to meet the requirements of reducing component heat loss, it is necessary to add insulation material with a thickness of 20mm or more on the inward side of the concealed roller shutter packaging box, and the gaps can be sealed with sealing strips.

本文由濟南卷簾門友情奉獻.更多有關的知識請點擊:http://www.cxfk.net.cn真誠的態度.為您提供為的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

This article is dedicated by Jinan Roller Shutter Door. For more information, please click: http://www.cxfk.net.cn Sincere attitude. We will provide you with comprehensive service. We will gradually contribute more relevant knowledge to everyone. Stay tuned