1、在電動卷簾門的使用過程中，要盡量保持控制器和電壓的穩定，禁止安裝在非常潮濕的環境，另外不要隨意打開遙控器，如若發現門體上有電線纏繞、打結等應及時處理。注意通道的是否堵塞，阻礙門體下降，如若發生異響應立即停止電機運作。

1. During the use of electric roller shutter doors, it is important to maintain the stability of the controller and voltage as much as possible. It is prohibited to install them in very humid environments. Additionally, do not open the remote control casually. If any wires or knots are found on the door body, they should be dealt with promptly. Pay attention to whether the channel is blocked, hindering the descent of the door body. If there is any abnormal response, immediately stop the motor operation.

2、要經常性的檢查電動卷簾門上下行程的開關，對行程控制器加上潤滑油，保持正常良好的運行，另外，操作人員手動控卷簾門，檢查器運行情況，校對上下行程開關位置，使電動卷簾門開啟或關閉時處于適當位置，且檢查過程中嚴防電動卷簾門沖頂或沖底或者反轉，如若出現緊急情況應立即停止轉動，切斷電源。

2. Regularly check the switch of the up and down travel of the electric roller shutter door, add lubricating oil to the travel controller to maintain normal and good operation. In addition, the operator manually controls the roller shutter door, inspects the operation of the device, checks the position of the up and down travel switch, and ensures that the electric roller shutter door is in the appropriate position when opened or closed. During the inspection process, it is strictly forbidden for the electric roller shutter door to hit the top, bottom, or reverse. In case of emergency, the rotation should be stopped immediately and the power should be cut off.

3、操作員好是經常性的要檢查好電動卷簾門的手動開關和手動升降裝飾，以防止在緊急的情況下電動卷簾門會失靈，或者造成不必要的事故。

3. The operator should regularly check the manual switch and manual lifting decoration of the electric roller shutter door to prevent it from malfunctioning or causing unnecessary safety accidents in emergency situations.

4、要保持軌道運行暢通，及時清理電動卷簾門的軌道，保持內部清潔，卷簾門電機和傳動鏈條要經常加注潤滑劑，檢查控制箱內器件和開關控制盒，緊固接線端口，緊固螺絲等，清潔控制箱內、表面和按鈕上的灰塵污物，防止按鈕卡住而不能反彈。

4. To maintain smooth operation of the track, clean the track of the electric roller shutter door in a timely manner, maintain internal cleanliness, regularly add lubricant to the motor and transmission chain of the roller shutter door, inspect the components and switch control box inside the control box, tighten wiring ports, tighten screws, etc., clean the dust and dirt inside the control box, surface, and buttons to prevent the buttons from getting stuck and not rebounding.

本文由濟南卷簾門友情奉獻.更多有關的知識請點擊:http://www.cxfk.net.cn真誠的態度.為您提供為的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

This article is dedicated by Jinan Roller Shutter Door. For more information, please click: http://www.cxfk.net.cn Sincere attitude. We will provide you with comprehensive service. We will gradually contribute more relevant knowledge to everyone. Stay tuned